It may or may not surprise you, but I frequently get questions and sometimes criticism regarding the safety of my projects. There are also those rare occasions when people are even a little mean.

For example, I’m often asked if I get cut by the “razor sharp” aluminum cans. I can only say that I have cut hundreds of aluminum cans and rarely needed a bandaid. So I guess all I can say is be careful.

More recently, I received some criticism regarding this Crisco candle-making project. I mention it here because I am using these candles in today’s project. So, if you are fire-averse, beware.

For some reason, this post caused people to worry about my sleeping habits, implying that I might drift off after lighting my candle or that upon waking, I would choose to throw water on it to put it out.

I was admonished not to do these things.

One person even went so far as to suggest I should “rethink the post” as if to say I should take it down because it is just too dangerous. My initial reaction is always guilt because that’s how people in my generation were taught to feel when someone scolded them. But then I think, “Hey, wait a minute, I am not advocating blindfolded automobile navigation or even swimming within 30 minutes of eating a sandwich. I’m just making a candle here, people.” You know, candles. We humans have been using them for hundreds of years, and so far, they have not caused our extinction.

In what can only be considered an amusing side note, the Crisco candle post also garnered some unsolicited hatred towards microwaves. Yes, the poor microwave ended up as collateral damage of the-all-to-risky-Crisco-candle-experiment . As one reader put it, “microwaves should be banned,” and then it just got worse from there.

This just makes me wonder who are these people and what are they doing with their lives.

Anyway, due to my passive-aggressive nature, I did consider writing this post with every conceivable warning. But then I reminded myself that you, dear reader are an intelligent being capable of deciding for yourself what chances you are willing to take with your life. And besides, I am also way too lazy to warn you of every possible way in which you might injure yourself if you dare to take on this project. So let’s just go with a few general safety precautions.

• Hammers hurt if you hit yourself with them. Try not to do that.
• Flames can turn into bigger flames if you let them have more fuel. You should avoid letting that “fuel” be anything you don’t want to be turned into ash.
• Most craft projects should not be set on fire. But the really entertaining ones can be.
• Scissors and knives cut things. Please don’t use them on things you don’t want cut.
• Metal can edges can be sharp, but I wouldn’t recommend cutting a steak with them or using them for self-defense. Plan accordingly.

Here are a few other things you should know about me.

• I don’t believe Mcdonald’s should have to tell you their coffee is hot.
• I like to experiment hence the word lab in the name of my blog and YouTube channel.
• I believe my readers are NOT idiots. Well, most of them anyway. The ones that put sticks of dynamite in their microwaves, I’m not so sure about.
• Very few, if any, of my projects are original creations. Most are ideas from someone else with my own twist added. That’s my wheezily way of saying blame someone else for the danger.
• I believe paper cuts are survivable, and living is hazardous, but you should get out of bed anyway.

So you reckless daredevils with no regard for your safety, consider yourselves duly warned. This crafting stuff is treacherous business!

Go ahead, read on. I double dog dare you. 😁

.

Step 1 – Collect and Clean

You will need two cans to complete this project, but you may want to do more than one. Rinse both cans and remove and save both pull tabs.

Step 2 – Remove Top Can # 1

I use a tool called Draft Top to remove my can tops. You can find them for around 20 dollars, and there are also less expensive brands.

Your can should look like this once the top is removed.

If you would rather not buy a special tool, you can try this method, but I can not vouch for it as I have not personally tried it.

Step 3 – Mark and Cut Can # 1

To mark my cans, I used a Sharpie marker and some wooden blocks to draw a line around the top and the bottom of the can. The part in the middle is the waste material.

To cut the can, I punched a hole with a knife in the center of the waste area and then cut the can in half with scissors. Once I had the two pieces cut, I used scissors to trim off the excess can to make a clean edge on both pieces along the sharpie line.

Step 4 – Cut Can # 2

You will only use the pull tab and the bottom of the second can. But I like to save the rest of the can for other projects like making beads, garden markers, and even faux plants. To do this, I remove the can top and bottom with my knife and scissors and trim down the bottom with a pair of tin snips.

Step 5 – Gluing

To make the top fit a little more tightly, I added a coat of mod podge to the outside lip of the lid and the inside edge of the top piece allowing them to dry before fitting them together.

Once the Mod Podge was dry, I glued the domed bottom piece and the lid together with E6000 glue and added a “handle” to the top.

Then, I used needle-nosed pliers to bend the pull tabs to a 45-degree angle and attached them to the top piece of the can with the E6000 glue.

Step 6 – Assembly

You can assemble the piece by cutting a slit in the top or bottom piece. Cutting the bottom piece will hide the slit, but cutting the top piece leave the bottom intact for uses that require no leaking, as with the questionable Crisco candle example.

Step 7 – Finishing

You can leave the tins unfinished or decorate them with beads and kabobbles, spray paint them, and, my personal favorite, is to add the faux oxidized copper finish. You can check out this video for the tutorial.

Since some of my pieces will be outside, I also added a coat of DecoArt DuraClear Gloss Varnish.

Step 8 – Uses

I am sure you can think of more, but here are some possible uses.

Small jewelry box

Small gift box

Tiny Vase

Piggy Bank

Citronella Candles

Cheers and Happy Upcycling,

Cindy

Advertising Disclosure: Upcycle Design Lab may be compensated in exchange for featured placement of certain sponsored products and services or your clicking on links posted on this website.